How To Create A Photography Backdrop With Decorative Plaster

By | 29/11/2022

How to Make Your Own Textured Backdrops | Mastin Labs

Backdrops don’t accept to exist a major expense—you lot can brand your ain textured photography backdrops on a budget. I was able to create 2 elementary, yet versatile, foam backdrop boards for about $50. Each had its own unique texture, and pigment on both sides, which gave me four distinct looks.

Earlier we brainstorm, and fifty-fifty earlier telling you what supplies you might demand, let me first encourage you lot to truly make these your ain. You can do exactly what I did, just there are and so many other ways to texture these walls. For the walls in this article, I used plaster to create unlike textures and then painted them. Y’all could also hands do wallpaper or whatever other cloth y’all can become to stick to a thick sheet of styrofoam!

Supplies Yous Need to Build Your Ain Photography Backdrops

  • two – 2”x2’x4’ Foam Insulation Boards – Y’all can go for the thinner boards and save yourself a few dollars, but I really wouldn’t recommend annihilation less than an inch thick. Specially if you’re going to coat the board with lots of plaster equally I did. I went with the ii inch thick ones and honestly, had in that location been even thicker boards I would accept gotten them. Likewise, the thicker the lath, the easier it will stand on its own or with lite support.
  • Quick Spray Decorative Texture – This is a 50lb. bag of powder that you add water to and brand plaster. I used a lot of this stuff, and I still have over half of the purse left. Y’all can go for a saucepan of pre-mixed plaster, but it’s almost three times the toll and, if you’re using as much as I did, yous’ll run out quite quickly. I mixed mine in a ii-gallon saucepan with a chapeau.

    • (Notation: Y’all can mix this stuff by manus, but I encourage you to spend $6 on a paint mixer attachment for a drill and relieve your arm from certain expiry.)
  • Spray-On Wall Texture – This is what I used to create the knock-downwards texture on one side of the board. It was actually easy to do. I retrieve had I known just how easy, I would have simply done the aforementioned thing with the plaster I fabricated for the other wall textures. All the same, the ease of employ may be worth information technology. Anything that comes in a spray-on can is tempting. Wall texture, whipped foam, cheese. See what I mean?
  • Putty Knives – Truly, you could buy one of the cheap packs of plastic ones with various sizes. If you do want to go the nicer rout get a 4” knife and a ii” knife.
  • Trowel – Now we’re getting into the specific textures that I created. One of which was a plaster skip-trowel application to create a Venetian plaster wait. If you’re non doing this and take no other reason to utilize it, you lot won’t need this tool.
  • The beard of an old broom (or something else kind of like that). This one is besides specific to some of the textures I made. I just grabbed an onetime, plastic-bristled, studio broom and took the handle off of it.
  • Paint – Decide what colors you would like your walls to be and select your pigment. I went for a bright yellowish, a darker blue, and a grey.
  • Plastic Sheeting – You’re gonna make a mess!

Preparing Your Workspace to Build Your Photography Backdrops

Contemplate your piece of work area.You can work on these boards with them laid flat on the ground, or you lot can prop them upwards on a wall. I worked both means at various times, and each offers its own benefits and drawbacks. Standing upward means y’all’ll have to have a stool or step-ladder at some point. Laid apartment ways that you may have a hard time reaching over to apply plaster, paint, etc.

For the first couple of boards, I turned the sheet of styrofoam sideways and laid it flat confronting the wall length-wise. This worked well for the skip-trowel and knockdown textures. For the other ii, I laid the styrofoam flat.

Preparing your piece of work area makes such a huge difference! Sweep the flooring of your work surface, lay out your plastic, and organize all of your paint and tools. Make sure you know what sink or water source you lot’re going to apply and prepare that area.

How to Make Your Own Photography Backdrops

First, let me say that earlier making whatsoever of these, I had never done this before, or, bated from painting, used any of the techniques in creating them. I promise that yous’ll see this every bit an opportunity to accept fun, get a picayune messy, and make some art you can utilize to shoot with! I truly had a blast making all of these things!

How To Brand a Skip Trowel/Venetian Plaster Styled Photography Backdrop

up close of skip trowel texture

Tools/Supplies Needed:

  • Plastic sheeting to contain any mess.
  • Quick Spray Texture and bucket to mix it in.
  • Water for making the plaster.
  • A large putty knife.
  • A trowel.
  • Paint and painting supplies.

Adding h2o and mixing the plaster.

Step One: Mixing your plaster.

In your saucepan, toss in a skillful bit of the Quick Spray Texture. Add some cold water to it and mix it up well. If it’s thick and crumbly looking, add some more water. Your aim is a consistency that looks a lot similar pancake concoction (it doesn’t gustation like information technology). If you accidentally overdo it with the water and make it too thin, no worries. Just add together a petty more powder. I establish this stuff to exist super forgiving. Just make sure you mix it really well and get all the clumps out. I might even recommend sifting it into the bucket.

Step Two: Plaster Application.

Yous’re going to do this in three steps, with some drying time in between each one.

  • SKIM Glaze – This is the first pace. Cover the unabridged surface with the plaster, using alternating angles. See the above video for the specific technique. One time the surface is covered, let information technology dry for i hour before continuing.
  • TEXTURE Glaze – For this step, you lot’ll do a very like application, but assuasive the trowel to “skip” now and then to create more texture. Once covered, allow this glaze dry as well. one-2 hours.
  • SKIM Coat ii – This is a repeat of step one. Utilise the plaster at a low angle, scraping information technology off at a high angle. Continue to change the direction of your wrist while doing this. Allow to dry for an hour.

In the video to a higher place, she is applying an actual Venitian plaster, which you lot sand after the 2d skim coat. Because I used regular plaster and painted my wall/board, I did not sand my wall. You can do this if you lot wish, but I am very happy with the outcome that I got.

Applying the start skim coat to the foam board. Edited with Mastin Labs Ektar 100 preset

Second texture coat. Edited with Mastin Labs Ektar 100 preset

Step Three: Painting your photography backdrops.

You want to retain the texture that you created with the plaster, so this means you lot shouldn’t pigment your new wall with a roller. Instead, use a big iv” flat paintbrush.

I painted my wall with two coats of paint, using only a 4” brush. Instead of painting in a single direction, I followed the lines and textures created from the skip trowel. I went across the entire surface in long, sweeping brush strokes. Also, on this beginning coat, I intentionally left areas unpainted here and there. This uneven coverage, and gaps in the pigment immune for a greater depth of texture once the second coat was applied.

Applying the get-go glaze of paint, making sure to leave gaps for texture. Edited with Mastin Labs Ektar 100 preset

shut up of gap textureEdited with Mastin Labs Ektar 100 preset

Later the start coat has dried (around 30 minutes – i hour), you can apply the second glaze. Use the same technique of sweeping castor strokes that follow the natural lines and textures of the skip trowel. This time, cover the unabridged board.

Depending on your color and how heavy your paint is, you might consider diluting the pigment with a picayune water. The thinner pigment volition allow greater depth in the application of multiple coats.

Applying the 2d coat. Edited with Mastin Labs Ektar 100 preset

Skater on skip trowel backdrop. Past Chris Daniels, edited with Mastin Labs Ektar 100 preset

How To Brand a Knockdown Textured Styled Photography Backdrop

up shut of knockdown texture

Tools/Supplies Needed:

  • Plastic sheeting to incorporate any mess.
  • i tin of Spray On Wall Texture.
  • A large putty knife, trowel or duster.
  • Paint and painting supplies.

This is the easiest and virtually straightforward application of the four textures in this tutorial. Though I believe yous could easily make this using the same plaster from the skip trowel (using a slightly thinner consistency), I’m going to show you how to create it out of a tin, using Spray On Wall Texture. That’s what I did, and it was crazy easy!

Y’all can lay your board flat or place it upwards against a wall. Whatever works best for you. Be sure to lay out the plastic to keep things clean.

Step One: Spray Information technology On.

Actually. It’south that uncomplicated. Y’all can merely follow the direction on the can.

Spray it on in a circular motility. I did about a third of the board at a time.

Allow information technology to dry for 1-2 minutes.

Spray on the texture in circular motions

Step Ii: Knock It Down.

Using a larger putty knife, or even a squeegee or trowel, verylightly sweep the edge beyond the plasterknocking it downwardly or flattening it.

knock it down in alternating, sweeping motions

Echo steps one and two until the entire foam board is covered.

You can opt to practice some other layer on superlative for even more texture. I did.

Step Three: Paint Information technology.

Nothing fancy here. Pick your color and apply information technology with a roller, brush, or whatever y’all wish. Paint information technology just equally you would a wall in your home. Let it dry and shoot on it!

Portrait of studio buddy, Steve on knockdown texture. By Chris Daniels, edited with Mastin Labs Ilford PanF preset

How To Make a Heavy Plaster Gratuitous Class Styled Photography Backdrop

up close of free class textures fabricated with broom

These are really fun to do! Remember that old broom head from our supply list? Here’s where information technology comes in handy!

You’ll most likely desire to lay the boards flat for these. I initially tried to exercise the first 1 with the cream standing up, and information technology didn’t become so well.

Painting the two freeform texture boards

Tools/Supplies Needed:

  • Plastic sheeting to contain any mess.
  • Quick Spray Texture and bucket to mix information technology in.
  • H2o for making the plaster.
  • Broom head (or similar bristled brush).
  • H2o to dip the broom in.
  • A large putty knife.
  • Paint and painting supplies.

Step One: Mix The Plaster.

You’re going to use the same process for mixing plaster for the skip trowel, but this time you’re going to make a lot more. Especially if y’all’re roofing two boards as I did. If you are doing two boards, you’re going to make almost a gallon of plaster. You’re going for that aforementioned pancake batter consistency, and be sure to mix all the lumps out, or they’ll prove up on the wall.

Stride 2: Schmear it Like Cream Cheese.

At present, using your large putty knife, take your plaster-concoction and spread it all over the board. Heck, If you really want to go for it, use your hands or even dump some on the board and spread it around. Go crazy! Just get it out of the saucepan and spread evenly beyond the foam.

Stride Three: Sweep It!

Dip the broom or brush in a flake of h2o and sweep it across the plaster to brand shapes and patterns. In that location is no specific instruction here. Just accept fun with it and make lines and shapes that you similar. Experiment. Remember to wet the beard every once in a while. The wetting helps proceed the plaster from building up on the broom too much. If the bristles practise get too heavy, you can scrape off the plaster or even wash the broom if you lot want a clean offset.

Using the aforementioned broom, I made two different textures. The beginning was more patterned. I started from the top of the board and made little overlapping rainbow shapes all the way down.

The 2d was more freeform. I did long, overlapping strokes with the broom, which concluded upwards looking kind of like a ribboned texture.

Step Three: Paint

Really, you can practice whatever you desire here, just I used that same cheap 4″ flat paintbrush. Simply like with the skip trowel, I painted with the grain of the texture and left some unpainted spots here and there on the first glaze for more depth.

Painting the boards

That’southward pretty much information technology for these, friends! I actually promise that you take a lot of fun making these and please show usa what y’all make and how y’all use them! Equally e’er, never hesitate to reach out to me with any questions or comments! Here are a few images I’ve taken so far one the ones I created:

Top Left Edited with Mastin Labs Fuji Original | Acme Right Edited with Mastin Labs Portra 160+ | Bottom Images Edited with Mastin Labs Ektar 100

Source: https://mastinlabs.com/blogs/photoism/how-to-make-your-own-textured-backdrops

Posted by: Fusiontr.com

Originally posted 2022-02-12 23:53:21.